| 1. | Standard of test method for surface load capacity of gears
齿轮接触疲劳强度试验方法 |
| 2. | The influence of surface load to critical affection depth in goaf
地面荷载对地下采空区的临界扰动深度及其影响 |
| 3. | Must be in the service container before the design surface loads
必须位于服务容器中，然后才能加载设计图面。 |
| 4. | The shear - lag effects were mainly analyzed under surface load and focus load , and the different was dissnssed that impact to dynamic analysis of these two models
所得的分析结果对指导这类桥梁的设计具有重要的工程实用价值。 |
| 5. | Standard test method for microvacuum sampling and indirect analysis of dust by transmission electron microscopy for asbestos structure number surface loading
用石棉结构值表面负荷用透射电子显微镜对尘埃微真空取样和间接分析的标准试验方法 |
| 6. | Different from cyclic loading acted on onshore foundation , the wave pressure plays double roles as : the surface loading imposed on the mudline and the boundary condition of excess pore pressure
与常规陆上荷载不同，波压力不仅是外加的循环表面力，而且是海床表面的超静孔隙水压力边界条件。 |
| 7. | In chapter 3 , we briefly present the fundamental theory of the elastic response of a spherical earth to the surface loads and the treatment to the loading effects of the barometric pressure
第三章：简述球形弹性地球负荷响应解的基础理论和大气负荷效应的处理方法；建立大气重力和倾斜格林函数表达式 |
| 8. | The heater is cooking heat source in the microwave oven . generally 2 pcs . as one suite in series and the power of single tube is 400w 600w . bigger surface load and higher radiating coefficient make the microwave cooking food more quickly
本加热器在微波炉中为烧烤热源，一般一组为2只串联使用，单管功率一般为400w600w ，表示负荷较大，且石英管表示的热辐射系数高，使微波炉烧烤食物更加快捷。 |
| 9. | After determining the max furnace temperature , calculate the power ( kw ) of a single element using the way of multiplying the stipulated surface load of the elements under said furnace temperature ( find it out from the above table ) by the surface area of hot zone of the elements . ( find it out from the product dimension
确定最高炉温后，根据元件在此炉温下所规定的表面负荷，乘以所选元件发热部的表面积（从产品规格表中查出） ，求出单支元件的功率( kw ) 。 |
| 10. | The surface loading of the mountains and the associated root of thickened crust produce horizontal deviatoric tension in the strong upper crust . in contrast , the deep , dense lithospheric root and its associated downflexing of the surface produce horizontal compressive deviatoric stress in the strong near - surface layer . the actual state of stress in the strong layer of the upper crust is the combined effect of these two opposite stress systems together with bending and other local and regional stresses such as due to ridge push
模拟结果表明：由于均衡机制，造山带下部的低密度山根促使地壳隆升、造山，山根是地壳刚性层中张性构造应力的主要力源；与此相反，冷的高密度岩石圈向软流圈插入、拆离、下沉，从而形成岩石圈根，它引起挤压造山和岩石圈地幔物质的重新调整，也是地壳刚性层中挤压性构造应力的主要力源。 |
